abba stand adaptor - MVAgusta.net
 1Likes
  • 1 Post By noggin
 
LinkBack Thread Tools Display Modes
post #1 of 8 (permalink) Old 04-10-2016, 11:27 AM Thread Starter
New Member
 
stevebdiver's Avatar
 
Join Date: Apr 2016
Location: Fife, Scotland
Posts: 12
abba stand adaptor

Hi new here, was wondering if anyone could confirm if the brutale adaptor kit is ok for the dragster rr...abba website doesn't list one specifically .....cheers
stevebdiver is offline  
Sponsored Links
Advertisement
 
post #2 of 8 (permalink) Old 04-10-2016, 03:44 PM
Senior Member
 
Red800's Avatar
 
Join Date: Jul 2014
Location: Somerset UK
Posts: 431
New Site Garage
I think they should be ok for the dragster, I had one for brutale but I didn't think it lifted the bike high enough unless I put it on a certain part of the ground, it dragged the back wheel when cleaning/lubing the chain, I phoned abba about it and they denied there was a problem but I think Ackers had a similar issue with his brutale as well when using the stand.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


Bruce
MY15
Edition1 Turismo
Red800 is offline  
post #3 of 8 (permalink) Old 04-10-2016, 05:26 PM
New Member
 
Join Date: Sep 2015
Posts: 36
Works fine on my b3, the rear wheel spins freely. Ymmv
Blitzen is offline  
Sponsored Links
Advertisement
 
post #4 of 8 (permalink) Old 04-10-2016, 06:05 PM
Established Member
 
r6ymy's Avatar
 
Join Date: Sep 2015
Location: Witney, Oxfordshire
Posts: 189
ABBA told me the fitting kit is the same for all recent MV. Fits my Turismo but needs a 30mm sheet of MDF under the stand for the back wheel to clear the floor. Should be fine as is for a Dragster.

Neville
Turismo Veloce
r6ymy is offline  
post #5 of 8 (permalink) Old 04-10-2016, 06:22 PM Thread Starter
New Member
 
stevebdiver's Avatar
 
Join Date: Apr 2016
Location: Fife, Scotland
Posts: 12
Thanks for the info, I'll get it ordered!
stevebdiver is offline  
post #6 of 8 (permalink) Old 04-11-2016, 12:31 AM
Senior Member
 
Ackers's Avatar
 
Join Date: Jun 2013
Location: Dorset, UK
Posts: 2,210
New Site Garage
Yep on the Brutale 800 and I suspect the dragster too you need a piece of board under the stand to lift the back wheel up off the floor, on a new tyre that is, once it's been flat spotted a bit they're OK.

Same issue with my Stradale. The Abba kit is for the B4 Brutale but fit the 3 cylinder range but the swing arm pivot point on the 3 cylinders is higher than the B4's that's why it won't quite lift the wheel off the floor. Abba are aware of this but don't mention it

You also might find you need to use a needle file on the inside of the sleeve that fits over the bolt head as its a tight fit?

Interested in anything that Sucks, Bangs and Blows!
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Ackers is offline  
post #7 of 8 (permalink) Old 01-02-2019, 12:34 AM
Established Member
 
Manic's Avatar
 
Join Date: Dec 2018
Location: Whangarei, New Zealand
Posts: 82
New Site Garage
Hey there ... I just checked on the fitting kit (going from CB1300) to a Stadale and it shows this:

Fitting Kit for MV Brutale 55.00 1 55.00
MV V1 Hub Spindle for MV Brutale 45.00 1 45.00

Is the MV V1 hub thingy needed?

2015 Stradale
Manic is offline  
post #8 of 8 (permalink) Old 01-02-2019, 12:57 PM
New Member
 
noggin's Avatar
 
Join Date: Sep 2013
Location: Durham UK
Posts: 74
The hub spindle is only needed if you have the front lift arm, the front lift arm is an extra part you can buy to raise the front wheel off the ground.
Manic likes this.

Turismo Veloce
Brutale 920
noggin is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to use all of the features of the MVAgusta.net site, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome