Question about rear hub bearing - MVAgusta.net
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 15 (permalink) Old 04-06-2016, 12:30 PM Thread Starter
New Member
 
Join Date: Jul 2014
Location: Sao Paulo Brazil
Posts: 25
Question about rear hub bearing

I saw several topics about rear hub bearing failure. In fact, my B4 bearing collapsed below 10K Km.
Reading a lot of posts about that, people says that fail occurs due to an excessive torque (above 20Nm) at certain bolts, but I didn't realize which bolts are.
If one of you coud show me a photo or picture where I can see the bolts, or give me catalog number of these, I will apreciate.

Thanks in advance. My B4 is 910S 2008.

PS: Sorry, my english is very bad
tu-barao is offline  
Sponsored Links
Advertisement
 
post #2 of 15 (permalink) Old 04-06-2016, 12:41 PM
Senior Member
 
silentservice703's Avatar
 
Join Date: Feb 2008
Location: Duxbury, MA, USA
Posts: 20,800
Send a message via Skype™ to silentservice703
Name:  1090RR Swingarm.jpg
Views: 291
Size:  200.4 KB

Gapalicious 2019 at
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
from OCTOBER 2-6, 2019

Call (423) 519-2000 or (423) 253-6213 to reserve your Riverfront Cabin. PM me for The Crow's Nest reservation!!!

Email/Paypal:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


My personal Cell Phone: (781) 223-3020


'07 F4 312R, '10 B4 1090RR, '15 B3 800RR
'07 Ducati Monster S4Rs, '07 Ducati Monster 695
2010 Harley Davidson Ultra-Classic Electra-glide CVO FLHTCUSEBLK
'63 Honda C100A Cub
'61 MVA TRA 125
silentservice703 is offline  
post #3 of 15 (permalink) Old 04-06-2016, 12:42 PM
Senior Member
 
silentservice703's Avatar
 
Join Date: Feb 2008
Location: Duxbury, MA, USA
Posts: 20,800
Send a message via Skype™ to silentservice703
Chain adjustment seems to play a role, too.

Gapalicious 2019 at
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
from OCTOBER 2-6, 2019

Call (423) 519-2000 or (423) 253-6213 to reserve your Riverfront Cabin. PM me for The Crow's Nest reservation!!!

Email/Paypal:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


My personal Cell Phone: (781) 223-3020


'07 F4 312R, '10 B4 1090RR, '15 B3 800RR
'07 Ducati Monster S4Rs, '07 Ducati Monster 695
2010 Harley Davidson Ultra-Classic Electra-glide CVO FLHTCUSEBLK
'63 Honda C100A Cub
'61 MVA TRA 125
silentservice703 is offline  
Sponsored Links
Advertisement
 
post #4 of 15 (permalink) Old 04-06-2016, 12:49 PM Thread Starter
New Member
 
Join Date: Jul 2014
Location: Sao Paulo Brazil
Posts: 25
I will verify these bolts torque and chain adjustment, to avoid 2nd collapse

Thank you very much!
tu-barao is offline  
post #5 of 15 (permalink) Old 04-06-2016, 03:17 PM
Senior Member
 
eddypro's Avatar
 
Join Date: Feb 2011
Location: brisbane
Posts: 3,493
In my opinion, and just checked mine again.Water does the damage.Tighten to 28nm and checked regularly.
If I where you a would consider a Mitchy hub.I never Wash my bike using Water.

cheers eddy
eddypro is offline  
post #6 of 15 (permalink) Old 04-06-2016, 03:22 PM
Senior Member
 
eddypro's Avatar
 
Join Date: Feb 2011
Location: brisbane
Posts: 3,493
If you are going to replace the bearing only use INA BEARING ,Now done 40,000 km and still going OK.Others will have different opinions.
eddypro is offline  
post #7 of 15 (permalink) Old 04-06-2016, 06:31 PM
Senior Member
 
theknurl's Avatar
 
Join Date: Jul 2009
Location: Palos Verdes Est, SoCal, USA
Posts: 13,796
Send a message via Skype™ to theknurl
Exclamation ????

Eddy;

The only bearings that have failed are INA bearings......why use them????

I tested the torque values on the pinch bolts which collapse the rear hub and the

3810-2RS bearing.....I posted the results

Do not use more than 15lbft/20Nm to avoid the problem

It is NOT water ingress...... It is damp air getting sucked in as the hub cools...

It is always the inside of the inner race that rusts

How would people that have never gotten the bike wet have rust any other way?

I've sold over 1000 bearings with zero reported failures......

MV can't say that

Noel-theknurl

The Forum Curmudgeon
I'm not PC either
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

'08 910R
'05 F4
ph. 310-414-7247 PST, GMT -8
PayPal;
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Skype; theknurl
theknurl is offline  
post #8 of 15 (permalink) Old 04-06-2016, 07:06 PM
Senior Member
 
eddypro's Avatar
 
Join Date: Feb 2011
Location: brisbane
Posts: 3,493
Noel,i can only go by what is put in my bike,INA bearing and still perfect ,always at 28nm ,chain is as per spec,i have the hole in the bottom of the hub and i use a lot of grease,first bearing went at 18000km and there was rust marks everywhere on it,now if there was moisture it certainly would have destroyed my second bearing by now ,also it would depend on what part of the planet you live in and yes then wet and moisture would definitely come into play.

cheers eddy
eddypro is offline  
post #9 of 15 (permalink) Old 04-13-2016, 03:51 PM Thread Starter
New Member
 
Join Date: Jul 2014
Location: Sao Paulo Brazil
Posts: 25
Quote:
Originally Posted by eddypro View Post
In my opinion, and just checked mine again.Water does the damage.Tighten to 28nm and checked regularly.
If I where you a would consider a Mitchy hub.I never Wash my bike using Water.

cheers eddy
I was thinking about Mitchy Hub. But shipping cost to Brazil its very expensive, and now our currency have no value...
I have another parts to replace, I'm waiting for solution of political issues here to give more friendly exchange taxes

Thanks
tu-barao is offline  
post #10 of 15 (permalink) Old 04-13-2016, 03:55 PM
MVAgusta.net Sponsor
 
mitchy's Avatar
 
Join Date: Feb 2010
Location: Gold Coast, Australia.
Posts: 4,948
New Site Garage
Send a message via Skype™ to mitchy
PM sent.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Bike- F4 1078.
Work.Email & Paypal.

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Work Phone (+61)0755244655
Facebook- Mitch Covington
Mobile-0423041326
mitchy is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to use all of the features of the MVAgusta.net site, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome