F3: Body reassembly? Steering damper? - MVAgusta.net
 2Likes
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 13 (permalink) Old 05-22-2018, 06:41 PM Thread Starter
Senior Member
 
GCBC's Avatar
 
Join Date: Oct 2017
Location: USA East Coast
Posts: 290
Question F3: Body reassembly? Steering damper?

****UPDTED




























Been apart for ages, doesn't help I had 2 other bikes apart and a car during same time....
Mainly what order do they go back together and whats going on with the under tail and that heat sink? Theres no way the bolts holding the heat sink in went thru the under tail holding it up.
its a bitubo steering damper and that long black piece is going ontop/inside of the silver aluminum bit thats attached to the underside of the tank and theres practically no clearance on anything, anywhere, literally.

Bikes starting to look good tho!


Last edited by GCBC; 05-24-2018 at 09:57 AM.
GCBC is offline  
Sponsored Links
Advertisement
 
post #2 of 13 (permalink) Old 05-23-2018, 07:17 AM
Senior Member
 
silentservice703's Avatar
 
Join Date: Feb 2008
Location: Duxbury, MA, USA
Posts: 20,817
Send a message via Skype™ to silentservice703
As you noted, these bikes are very compact and sequenced together and apart.

Again, I will ask you, and anyone else asking for help to either start your post with "my bike is a _____ (year) _______ (model) ______(edition, i.e. Oro, etc..).
Or, you could simply edit your signature line to include that information so that each time you post a question about one of several dozen bike model/year combinations, those trying to help don't have to sift through all of your posts to figure out what bike.

Did you take this apart without the manual?

Gapalicious 2019 at
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
from OCTOBER 2-6, 2019

Call (423) 519-2000 or (423) 253-6213 to reserve your Riverfront Cabin. PM me for The Crow's Nest reservation!!!

Email/Paypal:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


My personal Cell Phone: (781) 223-3020


'07 F4 312R, '10 B4 1090RR, '15 B3 800RR
'07 Ducati Monster S4Rs, '07 Ducati Monster 695
2010 Harley Davidson Ultra-Classic Electra-glide CVO FLHTCUSEBLK
'63 Honda C100A Cub
'61 MVA TRA 125
silentservice703 is offline  
post #3 of 13 (permalink) Old 05-23-2018, 09:36 AM
Senior Member
 
Join Date: Nov 2014
Location: Germany
Posts: 392
ok lets start addressing one topic after another.
for the rear:
the bolts dont need to go through the black part. the way they are now is correct.
the holes on the front need 2 black plastic "pins" to then push in the red side panels. Hold the panels to the black piece and you will see how they all fit together. make sure they align when you put in the screws AND they align with the heat exchanger. Then everything back there should be sorted

as for the steering damper: didnt really get the issue? can you maybe type that out again?

MV F3 800 / 2014 / Quick shift up AND down working
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Nephalem is offline  
Sponsored Links
Advertisement
 
post #4 of 13 (permalink) Old 05-23-2018, 11:45 AM Thread Starter
Senior Member
 
GCBC's Avatar
 
Join Date: Oct 2017
Location: USA East Coast
Posts: 290
yes sorry I took it completely apart did a bunch of stuff and then had a delay up waiting on the headers for ever and ever then had to do 3 other projects while it was still completely apart, the body work is a puzzle that has been knocked off the table so to speak and ive forgotten which order arrangement it goes back. I have no manual for the bike. everything ive done I either figured out or asked on here.

I suppose the steering damper issue to put as eloquently as I can think to say, is that I dont have full steering range with it because it is scraping or binding up. (bike didn't come with one originally as you know). there is a silver aluminum bracket that is on the underside of the tank on the very front that has 2 bolts that attach it to the frame directly, I left the bracket on the tank but removed those two short bolts and inserted the long black damper mount inside of the aforementioned silver mount and stuck longer bolts thru both brackets sandwiching the original silver tank bracket between the frame of the bike and the new long black damper mount. I have to have the damper sorted completely during the tank install as I cant redo anything after tank is set. I got the entire damper mount & kit from someone on here who ran it on an 800 I believe.

So is it in order of reassembly
damper/tank
undertail tray/long red side pieces together
then ?????
?????
big side panels last
GCBC is offline  
post #5 of 13 (permalink) Old 05-24-2018, 03:55 AM
Senior Member
 
Join Date: Nov 2014
Location: Germany
Posts: 392
I usually do it that way:
tank with tank mount of steering damper
tail section
seat
entire "front" fairing, so side panels and metal heat shielding (you don't have to disassemble those, they can be taken off as one piece for each side, make sure the oil radiator guard sits correctly!)
steering damper mount to top triple with steering damper still installed

this way you only have to remove the 2 screws below the top triple and the one that attaches the steering damper to the tank mount bracket

also just to add: there are manuals available for free on Donsy's website

MV F3 800 / 2014 / Quick shift up AND down working
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Nephalem is offline  
post #6 of 13 (permalink) Old 05-24-2018, 07:01 AM
Senior Member
 
silentservice703's Avatar
 
Join Date: Feb 2008
Location: Duxbury, MA, USA
Posts: 20,817
Send a message via Skype™ to silentservice703
Manuals: Team Double 3 Racing | MV Agusta

Gapalicious 2019 at
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
from OCTOBER 2-6, 2019

Call (423) 519-2000 or (423) 253-6213 to reserve your Riverfront Cabin. PM me for The Crow's Nest reservation!!!

Email/Paypal:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


My personal Cell Phone: (781) 223-3020


'07 F4 312R, '10 B4 1090RR, '15 B3 800RR
'07 Ducati Monster S4Rs, '07 Ducati Monster 695
2010 Harley Davidson Ultra-Classic Electra-glide CVO FLHTCUSEBLK
'63 Honda C100A Cub
'61 MVA TRA 125
silentservice703 is offline  
post #7 of 13 (permalink) Old 05-24-2018, 09:47 AM Thread Starter
Senior Member
 
GCBC's Avatar
 
Join Date: Oct 2017
Location: USA East Coast
Posts: 290
GCBC is offline  
post #8 of 13 (permalink) Old 05-24-2018, 12:02 PM
Senior Member
 
Black_Gold_Saw's Avatar
 
Join Date: Jul 2016
Location: Netherlands
Posts: 1,582
New Site Garage
@2:35 in the video. The black push buttons are the same as the suzuki.
you probably just lost them.

Thats why you put these screws/bolts in plastic bags. Gets confusing real fast.
As for the rear belly fairing I'd suggest to zip tie it.

HP exhaust looks good.

"Mileena"
MV Agusta F3 675 '17 - Matt Avio Grey


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Black_Gold_Saw is online now  
post #9 of 13 (permalink) Old 05-24-2018, 12:04 PM
Senior Member
 
Join Date: May 2017
Location: Salem, Oregon
Posts: 526
The front portion of the bellypan, uses the bolts you have on the floor, as does the back of the bellypan, which should have a bracket that goes across it, like the front.
You should have 2 black plastic push pins for the undertray.
Your ram air covers use a M4 x.7x12, and yes you need a 15mm to work decently, due to the clearcoat resin where the bolt goes though the CF. What brand are you using?

Not familiar with you damper...

Is that exhaust bracket required by the rearset? most of the high mount only have the one that replaces the rear passenger pegs.
GCBC and GCBC like this.
jdgun is online now  
post #10 of 13 (permalink) Old 05-24-2018, 02:23 PM
Senior Member
 
airjawed's Avatar
 
Join Date: Apr 2017
Location: Memphis
Posts: 564
New Site Garage
The rear undertray normally attaches to the stock exhaust resonator box. Not sure what is done when the exhaust is changed out like in your case. Maybe try and fab something similar to the bracket going accross the bottom of undertray on the front part.

If you go to say evolutinbike.it and pull up the parts diagrams you will see every bracket and screw that is used.
GCBC and GCBC like this.

2014 MV Agusta F3 800 ABS
airjawed is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to use all of the features of the MVAgusta.net site, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome