how to remove roller bearing from hub? - MVAgusta.net
 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old 11-13-2012, 02:37 PM Thread Starter
Established Member
 
chay250's Avatar
 
Join Date: Aug 2008
Location: somerset. uk.
Posts: 159
how to remove roller bearing from hub?

any advice on how to remove/refit the large roller bearings from the hub ? i have managed to remove the right hand side bearing (the one that falls to pieces) but am not sure howto go about removing/refitting the roller bearings.
the rubber seals look like they could easily be damaged when refitting.
cheers colin
chay250 is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 11-13-2012, 03:05 PM
Senior Member
 
bogie1072's Avatar
 
Join Date: Jul 2009
Location: Florida and Sacramento
Posts: 1,093
removed seals
remove snap rings...these are kind of a pain to remove
press out bearing
I used a socket or sized washer to press it out.

I would replace the seals, the snap clips can be reused. The larger of the two clips can be purchased from ducati (998rs hub)..the other clip you would have to source if it broke.

If you are not replacing the race and bearings there really is no need to remove and refit just to clean and grease.

Last edited by bogie1072; 11-13-2012 at 03:09 PM.
bogie1072 is offline  
post #3 of 6 (permalink) Old 11-13-2012, 03:46 PM
Senior Member
 
theknurl's Avatar
 
Join Date: Jul 2009
Location: Palos Verdes Est, SoCal, USA
Posts: 11,654
Send a message via Skype™ to theknurl
Wink ?

Quote:
Originally Posted by chay250 View Post
any advice on how to remove/refit the large roller bearings from the hub ? i have managed to remove the right hand side bearing (the one that falls to pieces) but am not sure how to go about removing/refitting the roller bearings.
the rubber seals look like they could easily be damaged when refitting.
cheers colin
Colin leave the needle bearing where it is, clean and regrease it

anybody notice the seal are in BACKWARDS from the Factory

Noel-theknurl

The Forum Curmudgeon
i'm not PC either
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

'08 910R
'05 F4
ph. 310-414-7247 PST, GMT -8
email, PayPal;
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Skype; theknurl
theknurl is online now  
Sponsored Links
Advertisement
 
post #4 of 6 (permalink) Old 11-13-2012, 04:22 PM
Senior Member
 
bogie1072's Avatar
 
Join Date: Jul 2009
Location: Florida and Sacramento
Posts: 1,093
[QUOTE=theknurl;568196

anybody notice the seal are in BACKWARDS from the Factory[/QUOTE]

Yes but when you build a hub after a few glasses of wine who cares....forwards or backwards it don't matter can't see them with sprocket and wheel on.
bogie1072 is offline  
post #5 of 6 (permalink) Old 11-13-2012, 04:38 PM Thread Starter
Established Member
 
chay250's Avatar
 
Join Date: Aug 2008
Location: somerset. uk.
Posts: 159
thanks for that guys - i think i will take noels advice and leave them in place for now.
chay250 is offline  
post #6 of 6 (permalink) Old 11-13-2012, 05:40 PM
Senior Member
 
theknurl's Avatar
 
Join Date: Jul 2009
Location: Palos Verdes Est, SoCal, USA
Posts: 11,654
Send a message via Skype™ to theknurl
Wink

Quote:
Originally Posted by bogie1072 View Post
Yes but when you build a hub after a few glasses of wine who cares....forwards or backwards it don't matter can't see them with sprocket and wheel on.
i do the wine afterwards

Noel-theknurl

The Forum Curmudgeon
i'm not PC either
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

'08 910R
'05 F4
ph. 310-414-7247 PST, GMT -8
email, PayPal;
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Skype; theknurl
theknurl is online now  
Reply

Quick Reply
Message:
Options

Register Now



In order to use all of the features of the MVAgusta.net site, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome